British standard pipe thread

The British Standard Pipe thread (BSP thread) is a family of standard screw thread types that has been adopted internationally for interconnecting and sealing pipe ends by mating an external (male) with an internal (female) thread.

Types

Two types of threads are distinguished:

• Parallel ('straight') threads, British Standard Pipe Parallel thread (BSPP; originally also known as British Standard Pipe Fitting thread/BSPF and British Standard Pipe Mechanical thread/BSPM), which have a constant diameter; denoted by the letter G.
• Taper threads, British Standard Pipe Taper thread (BSPT), whose diameter increases or decreases along the length of the thread; denoted by the letter R.

These can be combined into two types of joints:

• Jointing threads: These are pipe threads where pressure-tightness is made through the mating of two threads together. They always use a taper male thread, but can have either parallel or taper female threads. (In Europe, taper female pipe threads are not commonly used.)
• Longscrew threads: These are parallel pipe threads used where a pressure-tight joint is achieved by the compression of a soft material (such as an o-ring seal or a washer) between the end face of the male thread and a socket or nipple face, with the tightening of a backnut.

Thread form

• the threadform follows the British Standard Whitworth standard
• symmetrical V-thread in which the angle between the flanks is 55° (measured in an axial plane)
• one-sixth of this sharp V is truncated at the top and the bottom
• the threads are rounded equally at crests and roots by circular arcs ending tangentially with the flanks
• the theoretical depth of the thread is therefore 0.64 times the nominal pitch

Pipe thread sizes

File:LogarythmTable.JPG

Example table of sizes from a German manufacturer

A list of 16 thread sizes are defined by the standards, ranging from ¹⁄₁₆ to 6. The size number was originally based on the inner diameter measured in inches of a steel tube for which the thread was intended, but in the modern metric version of the standard is simply a size number.

Dash thread size	Thread size	Threads / in	Pitch (mm)	Thread major diameter		A/F (mm)	Gauge length (mm)		Corresponding pipe				Tapping drill size (mm)
				(mm)	(in)				DN	OD (mm)	OD (in)	Thickness (mm)	BSP.PL (Rp)	BSP.F (G)
	0.0625	28	0.907	7.723	0.304		4						6.60	6.80
−2	0.125	28	0.907	9.728	0.383	15	4		6	10.2	0.40	2	8.60	8.80
−4	0.25	19	1.337	13.157	0.518	19	6		8	13.5	0.53	2.3	11.50	11.80
−6	0.375	19	1.337	16.662	0.656	22/23	6.4		10	17.2	0.68	2.3	15.00	15.25
−8	0.5	14	1.814	20.955	0.825	27	8.2		15	21.3	0.84	2.6	18.75	19.00
−10	0.625	14	1.814	22.911	0.902				16			2.6	-	21.00
−12	0.75	14	1.814	26.441	1.041	32	9.5		20	26.9	1.06	2.6	24.25	24.50
−16	1	11	2.309	33.249	1.309	43	10.4		25	33.7	1.33	3.2	30.40	30.75
−20	1.25	11	2.309	41.910	1.650	53	12.7		32	42.4	1.67	3.2	39.00	39.50
−24	1.5	11	2.309	47.803	1.882	57	12.7		40	48.3	1.90	3.2	45.00	45.00
−32	2	11	2.309	59.614	2.347	70	15.9		50	60.3	2.37	3.6	56.75	57.00
	2.5	11	2.309	75.184	2.960		17.5		65	76.1	3.00	3.6
	3	11	2.309	87.884	3.460		20.6		80	88.9	3.50	4
	4	11	2.309	113.030	4.450		25.5		100	114.3	4.50	4.5
	5	11	2.309	138.430	5.450		28.6		125	139.7	5.50	5
	6	11	2.309	163.830	6.450		28.6		150	165.1	6.50	5

The major diameter listed is the outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" from the small end of the thread. The taper is 1 to 16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.

Pipe thread designations

These standard pipe threads are formally referred to by the following sequence of blocks:

• the words "Pipe thread",
• the document number of the standard (e.g., "ISO 7" or "EN 10226")
• the symbol for the pipe thread type:
  • G = external + internal parallel (ISO 228)
  • R = external taper (ISO 7)
  • Rp = internal parallel (ISO 7/1)
  • Rc = internal taper (ISO 7)
  • Rs = external parallel
• the thread size

Threads are normally right-hand. For left-hand threads, the letters "LH" are appended.

Example: Pipe thread EN 10226 Rp 2½

The terminology for the use of G and R originated from Germany (G for gas, as it was originally designed for use on gas pipes; R for rohr (meaning pipe).)

See also

AN thread British standard brass thread Garden hose thread National pipe thread

Panzergewinde Thread angle Threaded pipe

External links

• Newman Tools Inc. and J.W. WINCO, INC. show the Whitworth form BSP or ISO pipe thread.