Rocket engine nozzle

Figure 1: A de Laval nozzle, showing approximate flow velocity increasing from green to red in the direction of flow

Nozzle on the first stage of an RSA-3 rocket

A rocket engine nozzle is a propelling nozzle (usually of the de Laval type) used in a rocket engine to expand and accelerate the combustion gases produced by burning propellants so that the exhaust gases exit the nozzle at hypersonic velocities.

History

The de Laval nozzle was originally developed in the 19th century by Gustaf de Laval for use in steam turbines. It was first used in an early rocket engine developed by Robert Goddard, one of the fathers of modern rocketry. Subsequently, almost all rocket engines used this idea, including Walter Thiel's implementation which made possible Germany's V2 rocket.

Atmospheric use

The optimal size of a rocket engine nozzle to be used within the atmosphere is when the exit pressure equals ambient pressure, which decreases with altitude. For rockets travelling from the Earth to orbit, a simple nozzle design is only optimal at one altitude, losing efficiency and wasting fuel at other altitudes.

If the pressure of the jet leaving the nozzle is above ambient pressure then a nozzle is said to be 'underexpanded'; if the jet is below ambient pressure then it is 'overexpanded'.

Slight overexpansion causes a slight reduction in efficiency, but otherwise does little harm. However, if the jet pressure is approximately 40 percent of ambient then 'flow separation' occurs. This can cause jet instabilities that can cause damage to the nozzle or simply cause control difficulties of the vehicle or the engine.

In some cases it is desirable for reliability and safety reasons to ignite a rocket engine on the ground that will be used all the way to orbit. For optimal liftoff performance, the nozzle should be ambient at sea-level; however, if a rocket engine is primarily designed for use at high altitudes and is only providing additional thrust to another "first stage" engine during liftoff in a multi-stage design, then designers will usually opt for an overexpanded (at sea-level) design. This was the technique employed on the Space shuttle's main engines, which spent most of their powered trajectory in near-vacuum while the shuttle's two Solid Rocket Boosters provided the majority of the liftoff thrust.

Vacuum use

For nozzles that are used in vacuum or at very high altitude, it is impossible to match ambient pressure; rather, larger area ratio nozzles are usually more efficient. However, a very long nozzle has significant mass, a drawback in and of itself. A length that optimises overall vehicle performance typically has to be found. Additionally, as the temperature of the gas in the nozzle decreases some components of the exhaust gases (such as water vapour from the combustion process) may condense, or even freeze. This is highly undesirable and needs to be avoided.

Magnetic nozzles have been proposed for some types of propulsion (for example VASIMR), in which the flow of plasma or ions are directed by magnetic fields instead of walls made of solid materials. These can be advantageous since a magnetic field itself cannot melt and the plasma temperatures can reach millions of kelvins. However, there are often thermal design challenges presented by the coils themselves, particularly if superconducting coils are used to form the throat and expansion fields.

1-D Analysis of gas flow in rocket engine nozzles

File:Nozzle de Laval diagram.svg

Diagram of a de Laval nozzle, showing flow velocity (v) increasing in the direction of flow, with decreases in temperature (t) and pressure (p). The Mach number (M) increases from subsonic, to sonic at the throat, to supersonic.

Main article: De Laval nozzle

The analysis of gas flow through de Laval nozzles involves a number of concepts and assumptions:

For simplicity, the combustion gas is assumed to be an ideal gas.
The gas flow is isentropic (i.e., at constant entropy), frictionless, and adiabatic (i.e., there is little or no heat gained or lost)
The gas flow is constant (i.e., steady) during the period of the propellant burn.
The gas flow is along a straight line from gas inlet to exhaust gas exit (i.e., along the nozzle's axis of symmetry)
The gas flow behavior is compressible since the flow is at very high velocities.

As the combustion gas enters the rocket nozzle, it is traveling at subsonic velocities. As the throat contracts down the gas is forced to accelerate until at the nozzle throat, where the cross-sectional area is the smallest, the linear velocity becomes sonic. From the throat the cross-sectional area then increases, the gas expands and the linear velocity becomes progressively more supersonic.

The linear velocity of the exiting exhaust gases can be calculated using the following equation ^[1]^[2]^[3]

\[V_e = \sqrt{\;\frac{T\;R}{M}\cdot\frac{2\;k}{k-1}\cdot\bigg[ 1-(P_e/P)^{(k-1)/k}\bigg]} \]

where:
\(V_e\)	= Exhaust velocity at nozzle exit, m/s
\(T\)	= absolute temperature of inlet gas, K
\(R\)	= Universal gas law constant = 8314.5 J/(kmol·K)
\(M\)	= the gas molecular mass, kg/kmol (also known as the molecular weight)
\(k\)	= \(c_p/c_v\) = isentropic expansion factor
\(c_p\)	= specific heat of the gas at constant pressure
\(c_v\)	= specific heat of the gas at constant volume
\(P_e\)	= absolute pressure of exhaust gas at nozzle exit, Pa
\(P\)	= absolute pressure of inlet gas, Pa

Some typical values of the exhaust gas velocity V_e for rocket engines burning various propellants are:

1.7 to 2.9 km/s (3800 to 6500 mi/h) for liquid monopropellants
2.9 to 4.5 km/s (6500 to 10100 mi/h) for liquid bipropellants
2.1 to 3.2 km/s (4700 to 7200 mi/h) for solid propellants

As a note of interest, V_e is sometimes referred to as the ideal exhaust gas velocity because it based on the assumption that the exhaust gas behaves as an ideal gas.

As an example calculation using the above equation, assume that the propellant combustion gases are: at an absolute pressure entering the nozzle of P = 7.0 MPa and exit the rocket exhaust at an absolute pressure of P_e = 0.1 MPa; at an absolute temperature of T = 3500 K; with an isentropic expansion factor of k = 1.22 and a molar mass of M = 22 kg/kmol. Using those values in the above equation yields an exhaust velocity V_e = 2802 m/s or 2.80 km/s which is consistent with above typical values.

The technical literature can be very confusing because many authors fail to explain whether they are using the universal gas law constant R which applies to any ideal gas or whether they are using the gas law constant R_s which only applies to a specific individual gas. The relationship between the two constants is R_s = R/M.

Specific Impulse

Thrust is the force which moves a rocket through the air, and through space. Thrust is generated by the propulsion system of the rocket through the application of Newton's third law of motion: "For every action there is an equal and opposite reaction". A gas or working fluid is accelerated out the rear of the rocket engine nozzle and the rocket is accelerated in the opposite direction. The thrust of a rocket engine nozzle can be defined as:^[1]^[2]^[4]^[5]

\(F\)	\(=\,\dot{m}\,V_e + (P_e - P_o)\,A_e\)
	\(=\,\dot{m}\,\bigg[V_e + \bigg(\frac{P_e - P_o}{\dot{m}}\bigg)A_e\bigg]\)

and for perfectly expanded nozzles, this reduces to:

\(F\)	\(=\,\dot{m}\,V_{eq}\)

The specific impulse, \(I_{sp}\), is the ratio of the amount of thrust produced to the weight flow of the propellants. It is a measure of the fuel efficiency of a rocket engine. It can be obtained from:^[6]

\[I_{sp} =\, \frac{F}{\dot{m}\,g_o}\,=\, \frac{\dot{m}\,V_{eq}}{\dot{m}\,g_o}\,=\,\frac{V_{eq}}{g_o}\]

where:
\(F\)	= gross rocket engine thrust, N
\(\dot{m}\)	= mass flow rate of exhaust gas, kg/s
\(V_e\)	= exhaust gas velocity at nozzle exit, m/s
\(P_e\)	= exhaust gas pressure at nozzle exit, Pa
\(P_o\)	= external ambient pressure, Pa (also known as free stream pressure)
\(A_e\)	= cross-sectional area of nozzle exhaust exit, m²
\(V_{eq}\)	= equivalent (or effective) exhaust gas velocity at nozzle exit, m/s
\(I_{sp}\)	= specific impulse, s
\(g_o\)	= Gravitational acceleration at sea level on Earth = 9.807 m/s²

In certain cases, where \(P_e\) equals \(P_o\), then:

\[I_{sp} =\, \frac{F}{\dot{m}\,g_o}\,=\, \frac{\dot{m}\,V_{e}}{\dot{m}\,g_o}\,=\,\frac{V_{e}}{g_o}\]

In cases where this may not be the case since for a rocket nozzle \(P_e\) is proportional to \(\dot{m}\), then it is possible to define a constant quantity which is the vacuum \(I_{sp}(vac)\) for any given engine thus:

\[I_{sp}(vac) =\,\frac{V_e}{g_o} + \frac{P_e\,A_e}{\dot{m}\,g_o}\]

and hence: \[F = I_{sp}(vac)\,g_o\,\dot{m} - A_e P_o\]

which is simply the vacuum thrust minus the force of the ambient atmospheric pressure acting over the exit plane.

Essentially then, for rocket nozzles, the ambient pressure acting over the engine largely cancels but effectively acts over the exit plane of the rocket engine in a rearward direction, while the exhaust jet generates forward thrust.

File:Rocket nozzle expansion.svg

Nozzles can be (top to bottom):
Underexpanded
Ambient
Overexpanded
Grossly overexpanded
If under or overexpanded then loss of efficiency occurs. Grossly overexpanded nozzles have improved efficiency, but the exhaust jet is unstable.^[7]

Aerostatic back-pressure and optimum expansion

As the gas travels down the expansion part of the nozzle the pressure and temperature decreases and the speed of the gas increases.

The supersonic nature of the exhaust jet means that the pressure of the exhaust can be significantly different from ambient pressure- the outside air is unable to equalize the pressure upstream due to the very high jet velocity. Therefore, for supersonic nozzles, it is actually possible for the pressure of the gas exiting the nozzle to go significantly below or very greatly above ambient pressure.

If the exit pressure is too low, then the jet can separate from the nozzle. This is often unstable and the jet will generally cause large off-axis thrusts, and may mechanically damage the nozzle.

This separation generally occurs if the exit pressure goes below roughly 30-45% of ambient, but may be delayed to far lower pressures if the nozzle is designed to increase the pressure at the rim, as is achieved with the SSME (1-2 psi at 15 psi ambient).^[8]

Other design aspects affect the efficiency of a rocket nozzle; the nozzle's throat should be a smooth radius. The angle of the narrowing down to the throat also has an effect on the overall efficiency, but this is small. The exit of the nozzle needs to be as sharp as possible to minimize the chances of separation problems at low exit pressures.

Advanced designs

A number of more sophisticated designs have been proposed for altitude compensation and other uses.

Nozzles with an atmospheric boundary include:

the expansion-deflection nozzle,^[9]
the plug nozzle and
the aerospike^[9]^[10].
the SERN, Single Expansion Ramp Nozzle, a linear expansion nozzle where the gas pressure transfers work only on one side and which could be described as a single-sided aerospike nozzle.

Each of these allows the supersonic flow to adapt to the ambient pressure by expanding or contracting, thereby changing the exit ratio so that it is at (or near) optimal exit pressure for the corresponding altitude. The plug and aerospike nozzles are very similar in that they are radial in-flow designs but plug nozzles feature a solid centerbody (sometimes truncated) and aerospike nozzles have a 'base-bleed' of gases to simulate a solid center-body. ED nozzles are radial out-flow nozzles with the flow deflected by a center pintle.

Controlled flow-separation nozzles include:

the expanding nozzle,
bell nozzles with a removable insert and
the Stepped nozzles or dual-bell nozzles^[11].

These are generally very similar to bell nozzles but include an insert or mechanism by which the exit area ratio can be increased as ambient pressure is reduced.

Dual-mode nozzles include:

the dual-expander nozzle and
the dual-throat nozzle.

These have either two throats or two thrust chambers (with corresponding throats). The central throat is of a standard design and is surrounded by an annular throat which exhausts gases from the same (dual-throat) or a separate (dual-expander) thrust chamber. Both throats would, in either case, discharge into a bell nozzle. At higher altitues where the ambient pressure is lower, the central nozzle would be shut off reducing the throat area and thereby increasing the nozzle area ratio. These designs require additional complexity but an advantage of having two thrust chambers is that they can be configured to burn different propellants or different fuel mixture ratios. Similarly, Aerojet has also designed a nozzle called the 'Thrust Augmented Nozzle'^[12] ^[13] which injects propellant and oxidiser directly into the nozzle section for combustion allowing larger area ratio nozzles to be used deeper in an atmosphere than they would without augmentation due to effects of flow separation. They would again allow multiple propellants to be used (such as RP-1) further increasing thrust.

Liquid injection thrust vectoring nozzles are another advanced design that allow pitch and yaw control from un-gimbled nozzles. India's PSLV calls its design 'Secondary Injection Thrust Vector Control System'; strontium perchlorate is injected through various fluid paths in the nozzle to achieve the desired control. Some ICBM's and boosters, such as the Titan IIIC and Minuteman II, use similar designs.

References

External links

[Nakka-1] 1.0 ^1.1 Richard Nakka's Equation 12

[Braeuning-2] 2.0 ^2.1 Robert Braeuning's Equation 2.22

[3] Script error

[NASAThrust-4] NASA: Rocket thrust

[NASASummary-5] NASA: Rocket thrust summary

[NASAIsp-6] NASA:Rocket specific impulse

[7] Script errorTechnical report

[8] PWR Engineering: Nozzle Design

[Sutton-9] 9.0 ^9.1 Script error p. 84

[10] Journal of Propulsion and Power Vol.14 No.5, "Advanced Rocket Nozzles", Hagemann et al.

[11] Journal of Propulsion and Power Vol.18 No.1, "Experimental and Analytical Design Verification of the Dual-Bell Concept", Hagemann et al.

[Thrust_Augmented_Nozzle-12] Thrust Augmented Nozzle

[TAN-13] THRUST AUGMENTED NOZZLE (TAN) the New Paradigm for Booster Rockets

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]